BLG20 CommissionerBuilt with Adsum IoT Coder · powered by Adsum Networks
no unit
fw ?
—
Stand next to the unit. Everything below is written over Bluetooth and read back from the unit's own account of itself — nothing is trusted because a button was pressed.
Open this on a phone. Scan with the camera and open the link in Chrome — Web Bluetooth needs Chrome on Android; iOS has none. The same page, the same address, no install:https://commission.adsumnetworks.com/blg20/
Defaults for every unit on this site. Saved on this device; export it to carry it to another phone.
Chrome lists nearby gateways; pick the one you are standing next to. The unit asks to pair the moment you connect — enter the six digits printed on its label.
A coordinate that cannot say how wrong it might be is worth nothing later, so every method carries an uncertainty and the rules differ by method. The unit refuses a position without one.
The device's own reported accuracy is the uncertainty. A phone with GPS outdoors gives a few metres; a laptop positions itself from Wi-Fi and will be tens of metres out — the tool will say which it got.
The label is how the unit appears on a dashboard; the identity is what the server knows it by. The key is generated here and shown once — the fleet register below is the only other place it exists.
The unit refuses this until it holds a position and a credential. That refusal is deliberate: this board has no satellite receiver, so a unit installed without a coordinate cannot use the satellite bearer at all — and nobody finds out for months.
Read the unit's own account of itself and compare it with what was written. Green is a match; anything else is the unit disagreeing, and the unit is right.
Every parameter a deployment needs, whether or not this unit's firmware exposes it yet. The tool reads the unit's service on connect: what it exposes is live, the rest is greyed with the reason. The greyed rows are the specification for the next firmware build.
| Parameter | Value | On this unit |
|---|
Every unit commissioned from this device. This is the record the platform side needs — the identity and key for the data plane, the position and provenance for the audit trail. Export it before you leave the site.
| when | unit | label | identity | key | lat | lon | ±m | method | fw | by |
|---|
Two lights, one per half of the unit. Colour is the state, the blink is the activity; every state is also distinguishable by pattern alone. From PLAN-2026-09-12-leds-buttons.
| LTE light (cellular half) | means |
|---|---|
| amber, slow 1 s blink | not commissioned — waiting for you |
| blue, 200 ms every second | searching for the network |
| green, one flash every 5 s | registered, resting between cycles — the normal state |
| solid blue, then green ×2 | sending, then acknowledged |
| red ×3 | a send failed; it will try next cycle |
| cyan where blue would be | on the satellite bearer |
| cyan, one flash every 3 s | satellite: waiting to attach — can take minutes |
| cyan / red alternating | satellite allowance used up; still working on cellular |
| amber ×2 then cyan | satellite refused: no commissioned position — set one |
| red, one flash every 2 s | data allowance exhausted — parked. This needs a visit |
| red / amber alternating | the modem is under a network attach ban: do not reset it, it clears itself in ~30 min |
| solid red | fault |
| BLE light (Bluetooth half) | means |
| off, green flash every 10 s | scanning normally |
| blue, slow breathe | commissioning window open — connect now |
| solid blue / fast blue | connected / waiting for you to enter the passkey |
| green flash + tick | a write was accepted |
| red ×2 + buzz | a write was refused — read status to see why |
| green ×3 + rising chirp | commissioned |
| three ticks, once | first data sent after commissioning — you can leave |
| amber flash every 5 s | store filling; the cellular half is behind |
| red flash every 2 s | the link between the two halves is down |
| The button (the small one; the other resets everything) | does |
| tap | identify: both lights white ×3, two ticks; the LTE light replays its state brighter for 5 s |
| hold 3–5 s | open the commissioning window for 5 minutes (or close it) |
| hold 10 s, red countdown | factory-reset the commissioning. Release early to cancel |
| hold while powering on | firmware recovery over USB |
BLG20 Commissioner · field tool v2 · built 11 September 2026 with Adsum IoT Coder · powered by Adsum Networks
Commissions an Adsum gateway from a Chrome tab over Web Bluetooth — no cable, no app, no phone signal needed. This tool, and the gateway firmware it commissions, were generated with Adsum IoT Coder from Adsum Networks — firmware that arrives already wired to the production tooling a device needs.
a05c0001-9e5f-4b6a-9f3a-2d1c7e4b8a01, firmware v1 characteristics …0002–…0006; proposed …0007–…000chttps://commission.adsumnetworks.com/blg20/ — the published copy; scan the QR at the topblg20-gateway/tools/commissioner.html — one file, no dependencies. Firmware: src/bm20-ble/src/provision.c